Відео

Also, the design is to keep your foot iff the pedal. Longer life.

Calibrate the clutch pedal. Key on, depress clutch, left power shuttle, listen for beep, slowly let pedal off until beep stops, continue releasing clutch slowly until beep comes back on. With clutch fully up, release power shuttle lever and turn key off for 5 seconds. Thanks.

Fascinating to see all your new adventures.

I have a Massey HD2650 it’s a smaller tractor then your. I purchased my used and it’s a 2010 year model and had roughly 300 hours on it. Bottom line the clutch went out at 400 hours. I use this tractor to ted and rake hay. I do use it to load hay with. When the clutch went I was loading and stacking round bales in the barn 4x4 bales no more then 650 lbs bales. During the replacement I went to the dealership and looked at the old clutch and the disk was literally trash the pressure plate had springs missing and the fiber material on the disks was just eaten up and mostly gone. I wasn’t hard on the tractor and it just didn’t make any sense to me that the clutch was trashed. The mechanic doing the work state by being use we don’t know how abusive the other(s) owners were. This model is a 74 HP with a Perkins engine the clutch looked to be about 9 to 10 inch clutch. The mechanic told me if I felt the clutch slipping to stop using the tractor until the clutch got readjusted. If I were you I would have a dealership mechanic check it out and save yourself the cost of clutch replacement and down time of the tractor. Good luck

E2 05 code slushn plez

awesomeeee!Thank you for this video!😊

Agzaga, haven’t bought a roll from Deere since we started buying from them. We’ve had great luck with the BaleTuff and Bridon, 0 issues with either.

🇺🇸🗽🛐💡👌

Used to watch all your videos...... Didn't realise you are back.. Now I am going to catch up again.... Good to have you back...

Nice of you to assist another channel .

My Son Has been envovled in Drag Racing ever since he learned to drive.... Has become very proficient with Blown, turbocharged Nitrous carburated and fuel injection..... He Just too delivery on a All aluminum Machined Ford 9.5 deck height small block, with a raised Cam centerline to facilitate installation of the Sonny Bryant 4;25 throw crank he bought 10 years ago....

Too bad you did not locate a 6 cylinder GM truck engine🗽🇺🇸🙏

In the past, I thought you advertised on several dedicated hay marketing websites❓Do those sites still exist ❓

Disappointed the 327 is being replaced .🇺🇸🗽🙏🐄

The channel needs consistent input to maintain viewer interest 🍶

Thank you for the videos! I really enjoy watching them and rewatching the old videos. I work full time and cut hay in the evenings so I understand where you are at. I’m just up the road in Limestone County.

Hello again from south GA

WELL, i never was really technically endowed, so the whole Video thing was a struggle, so my channel never improved beyond basics........ But the Hay Operation with production and sales is consistant.... We presently Convert Rounds into small squares... to Contracted Outlets ..

Thanks for this video! I really liked this video and cant wait for more.:)

My 5065e johndeer pto last used last year turn it on this year at pto rpms 1500 take off spend short time then stop at a alarm sound.

nice to see you posting again, thank you!

Truck is coming along nicely but I’m ready for some equipment and haying videos.

Turn a drum those machines are now extinct do the conversion there cheap now

What the price

'Promo sm'

Hello sir, glad to see you uploading again. Have been considering the 4707 for over a year. My dealer has one with the larger tires 34” rears. and the 931x loader. I asked about ordering the FL series loader and it was maybe 1500.00 more. Said they could have it in two weeks. Would you go with the higher capacity loader? Thanks for your input

Was,fuel pump for original engine, located as in-tank submersible type❓

🗽🇺🇸🙏👌

🇺🇸🗽🙏💯

🇺🇸🗽🐄

Maybe you should advertise and sell that motor, it should bring some good money. Then buy you a good 350 block and build it how you want it.

The two holes in the tailgate. Would have been a square emblem that said Electronic Spark Control. A lot of the 81s and 82s tailgates had that emblem in that exact spot

great looking truck!:) Could you maybe make walkaround of your current farm machinery you use?thank you!:)

What an awesome find!! Must be real miles unless someone did a full restoration 20 years ago or so.

Amazing!!!

Love the square body GM trucks. Looks very likely to be 47k miles to me judging by the pedals. Can't wait to hear it run. Looking forward to more videos as you have a way of filming and explaining better than all the other channels I tend to watch. Thanks for coming back and giving us more content!

It looks beautiful! Cant wait for more videos!Great looking truck!🤩

I noo :/ I hope you get a new job as soon as possible...😵‍💫

I really like how the squarebodys look,cant wait to see the truck.:) And the storys were great!(as always. :) )

*Promo SM*

remake the video. this was terrible sorry but not sorry

Kind of funny that they could not get the chip that destroys the engine during the pandemic.

I dont mind the noise....liked listening as always.(this time while learning for an exam^^) thanks for sharing! 340K miles, wow!

Your voice is nearly inaudible. You need to get to the point. Please remake this video and repost.

Thanks for the video. Unfortunately, it was kind of annoying with all the road noise in the back.

interesting storys,thank you for sharing!🙂

Is there any way to get land closer?

You need to do something about the sound. Its terrible.

These were known for water dripping on the distributor and plugging the vent with corrosion and when the moisture is stuck in the cap it causes the spark to jump to the module and kill it always carried 2 modules and a spare dizzy cap to get rid of moisture

Thanks for the video! Nice looking 515E!:) I would love to get a 315E for our lawn...maybe...who knows maybe iam lucky^^ do you still have the LA100 series mower? A little videoclip/storys would be great.:) I love everthing deere from mowers to the 9RX.:D